|
Please, look at this before you ask an MPCNC question. Thanks
|
|
1
|
2576
|
October 9, 2020
|
|
Network
|
|
1
|
74
|
November 6, 2026
|
|
Primo trucks not holding the bar square
|
|
8
|
162
|
October 20, 2026
|
|
Jackpot Intermittently panic reboots mid job, cannot read the panic reason
|
|
3
|
94
|
October 18, 2026
|
|
Fitment of idlers
|
|
19
|
260
|
October 15, 2026
|
|
Broken Bit...Why?
|
|
4
|
128
|
September 22, 2026
|
|
End Stop problems
|
|
2
|
106
|
September 21, 2026
|
|
Open-CNC-Shield - Motoren drehen aber nicht
|
|
41
|
350
|
September 12, 2026
|
|
Z-Axis Bearing Tension
|
|
2
|
72
|
September 7, 2026
|
|
Juddering...was working fine, now juddering like crazy
|
|
5
|
150
|
September 1, 2026
|
|
So many issues Primo
|
|
24
|
308
|
August 2, 2026
|
|
MPCNC and Fusion 360
|
|
2
|
106
|
July 27, 2026
|
|
Primo Wiring and Control
|
|
18
|
400
|
July 21, 2026
|
|
Issues with running TinyBee with TMC2209s in UART
|
|
6
|
229
|
July 10, 2026
|
|
MKS Gen L V2.1 and TMC2209 - stepper not moving
|
|
8
|
6334
|
June 23, 2026
|
|
MPCNC Primo SD Card Contents and .yaml file issues
|
|
6
|
162
|
June 8, 2026
|
|
Carving turned into drilling.... :(
|
|
8
|
261
|
June 8, 2026
|
|
Router is shifting the deeper it goes
|
|
10
|
172
|
May 27, 2026
|
|
Leadscrew Length?
|
|
1
|
106
|
April 21, 2026
|
|
MPCNC Elektrik
|
|
7
|
171
|
April 11, 2026
|
|
Kobalt trim router failure
|
|
31
|
479
|
April 10, 2026
|
|
SVGs to validate/calibrate belt tension?
|
|
1
|
101
|
April 6, 2026
|
|
MPCNC does not start cutting in the correct place
|
|
5
|
135
|
April 2, 2026
|
|
MPCNC original model from 2019 firmware
|
|
53
|
576
|
April 1, 2026
|
|
The Mini Rambo board has been taking a very long time to start up
|
|
1
|
58
|
March 31, 2026
|
|
X-Y Axis not running perpendicular
|
|
4
|
151
|
March 27, 2026
|
|
Laser Control boards
|
|
5
|
207
|
March 12, 2026
|
|
Jackpot 3 without endstops
|
|
4
|
137
|
March 8, 2026
|
|
Replace mini rambo control board
|
|
7
|
162
|
March 7, 2026
|
|
MPCNC Z-axis issue: Moving simultaneously with Y-axis (Arduino Uno + CNC Shield V3)
|
|
3
|
136
|
March 1, 2026
|