V1 Engineering Forum

Software / Firmware

Fusion360 Jackpot Board / FluidNC Issues with FluidNC, or the Jackpot CNC control Board? EstlCAM Sandify Klipper SKR Boards All info pertaining to the SKR Boards from Big Tree Tech. General GRBL Discussions about any of the grbl varieties are a good fit here.

Topic		Replies	Views	Activity
About the Software / Firmware category Software / Firmware		0	2806	November 23, 2019
SD Card Files Connected to Windows Network Drive Jackpot Board / FluidNC		8	97	June 3, 2025
iPad control not working Jackpot Board / FluidNC		9	185	June 3, 2025
FluidNC + 0–10 V Spindle Module: Spindle Always Runs at Constant Speed Software / Firmware		19	144	June 2, 2025
WebUI-3 release 3.0.0-4b1-FluidNC Jackpot Board / FluidNC		30	500	June 2, 2025
SKR Pro 1.2 Skulpfun s9 laser problems Software / Firmware		47	2953	May 31, 2025
Estlcam not recoverable to RGBL EstlCAM		23	205	May 30, 2025
FreeCAD 1.0 guide for importing XZ plates Software / Firmware		15	172	May 30, 2025
LR4 Jackpot error new setup Jackpot Board / FluidNC		3	34	May 30, 2025
Add Wifi to SKR Pro step by step SKR Boards		55	5961	May 29, 2025
Taking a closer look at the Jackpot and the EE involved with the Outputs Jackpot Board / FluidNC		18	86	May 29, 2025
Taking a closer look at the Jackpot and the EE involved with the Inputs Jackpot Board / FluidNC		47	236	May 28, 2025
FluidNC Macros Jackpot Board / FluidNC		9	324	May 28, 2025
Fusion 360 spoilboard surfacing Fusion360		1	54	May 28, 2025
Fusion 360 Post Processor MPCNC v3.0 (Beta 3) is Available Fusion360		2	98	May 27, 2025
Strange error GRBL		7	56	May 25, 2025
Using bluetooth instead of wifi with jackpot Jackpot Board / FluidNC		3	82	May 24, 2025
Endstops and motors in Estlcam EstlCAM		7	89	May 23, 2025
Taking a closer look at the Jackpot and the EE involved with the Power Supply Jackpot Board / FluidNC		54	239	May 22, 2025
Estlcam Weirdness with Part path on smaller diameter bit EstlCAM		8	136	May 21, 2025
SKR 1.4 Turbo Board problem with Laser engraving inline S commands EstlCAM		0	34	May 18, 2025
SKR 1.4 Turbo + BIGTREETECH TFT35 E3 V3.0.1 Problems with TFT Firmware SKR Boards		2	61	May 18, 2025
grblHAL on skr pro 1.2 SKR Boards		20	5106	May 18, 2025
Set default Jog distance to lowest value Jackpot Board / FluidNC		2	50	May 18, 2025
Fusion 360 Post Processor MPCNC v3.0 (Beta 1) is Available Fusion360		36	1137	May 16, 2025
Fusion360 Post Processing Stoppped Workihg Fusion360		2	107	May 16, 2025
Trouble homing Jackpot Board / FluidNC		5	67	May 15, 2025
CNC Cutter and laser engraver Software / Firmware		16	394	September 15, 2023
Tell tale signs - STA vs AP fallback? Jackpot Board / FluidNC		6	80	May 9, 2025
How to cook an ESP32 on your Jackpot (Don't do this) Jackpot Board / FluidNC		38	531	May 7, 2025